Jhon Harry's Blog

A Clever Mosaics self adhesive backsplash

The mosaic is increasingly used when you want to decorate a bathroom or kitchen for example. One can also decide to make an entire mosaic wall.
It's really not complicated to ask Such a coating is quick to install and can change in a jiffy the decoration of a whole room. Are you ready to follow our steps? Or you can choose to deal with a professional to save time when laying your mosaic.
[b]Prepare the pose [/b]
Whether you put a wall tile or a tapestry for example, it is always necessary that the support is well prepared This is also the case with a mosaic.
So that the glue adheres well on the support, it must be flat, clean and stable If it has rough edges, scrape it off and vacuum or sweep. If the support is covered with a lacquered paint, we advise you to polish it with a sanding then a good blow of sponge.
If the [b][url=https://clevermosaics.com/]Clever Mosaics self adhesive backsplash[/url] [/b]placed above a worktop, a catcher or a tiled surface and it simply serves as a frieze, your installation will begin by inserting braces But for a complete wall it's not the same. The plumb of the angle of the walls and the horizontality of the ground are not always good marks of precision In this case, follow these steps:
Raise the height of a mosaic tile to which you add the value of two thicknesses of joints.
[b]Draw a horizontal mark. [/b]
Attach a level horizontal pin and locate the start of the second plate laying on one side.
Attach a vertical cleat. These angular cleats define the start of the pose.
[b]Paste the mosaic
[/b]Buy a special glue ready for use Apply with a 5 mm V-tooth serrated spatula.
Pass the glue on a surface equivalent to two or three mosaic plates for the start. Streak the glue layer to give it its final thickness Place the first plate at the intersection of the wooden squareness Be careful to align the plate against the edges of the cleats.
Anchor the mosaic plate well in the glue. For this, gently squeeze it with a finishing trowel Continue laying the first row by inserting each plate with two spacer braces As you pose, with a tiler bat and a rubber mallet, lightly beat the surface of the plates Do so on the entire front row.
Cut out the last plate so that it fits the tight space. FYI, the frame glued to the back is cutter cutter For the following ranks, it's that easy. Cut a plate in half and then start the next row starting from the vertical cleat with this half-plate. You will have a staggered pose from one row to another.
Once the entire wall is covered with mosaic tiles, remove the cleats and cover the mosaic peripheral areas.
[b]How to make mosaic tile cutouts [/b]
If the cut is a multiple of the rows of small mosaic tiles, you simply cut the weft to the cutter.
By cons for a long straight cut it must be done on the back of the mosaic.
Then place the plaque on a martyr board and mark the cut line. Then lay a guide board and block between clamps.
You just have to follow the guidance with a grinder equipped with a diamond disc. Cut slowly by doing back and forth movements.
It may be that you are "embarrassed" by valves including taps In this case, locate and trace the outlines of the cuts in grease pencil.
Slice the weft to access the future waypoint and trim the small square (s) to be grinded with a mosaic peeler to cut straight or with a parrot clip if it is a curve Make the joints of my wall mosaic
You have almost finished laying your mosaic All you have to do is take care of the joints. Wait 24 hours after laying the plates and prepare mortar equivalent to an area of ??about 2m² to start. Garnish roughly by pushing the mortar with a finishing trowel. Then spread by pressing with the trowel to force the mortar to go to the bottom of the joints.
Run the trowel y to remove the excess but being careful not to dig the surface of the joints When the mortar begins to harden, rub in rotary passes with dry cloths Then apply a damp sponge to smooth the joints.
[b]Remember to rinse your sponge often with clear water[/b]
Wait a little longer until the setting is complete and rub the surface again with dry cloth. When everything is finished, wipe a wet sponge to remove the last traces.

Must be logged in to comment.